Strength and stability of frictional sliding of gabbro gouge at elevated temperatures   总被引：7，自引：1，他引：7  

Changrong He  Wenming Yao  Zeli Wang  Yongsheng Zhou   《Tectonophysics》2006,427(1-4):217

To investigate the strength of frictional sliding and stability of mafic lower crust, we conducted experiments on oven-dried gabbro gouge of 1 mm thick sandwiched between country rock pieces (with gouge inclined 35° to the sample axis) at slip rates of 1.22 × 10^− 3 mm/s and 1.22 × 10^− 4 mm/s and elevated temperatures up to 615 °C. Special attention has been paid to whether transition from velocity weakening to velocity strengthening occurs due to the elevation of temperature.Two series of experiments were conducted with normal stresses of 200 MPa and 300 MPa, respectively. For both normal stresses, the friction strengths are comparable at least up to 510 °C, with no significant weakening effect of increasing temperature. Comparison of our results with Byerlee's rule on a strike slip fault with a specific temperature profile in the Zhangbei region of North China shows that the strength given by experiments are around that given by Byerlee's rule and a little greater in the high temperature range.At 200 MPa normal stress, the steady-state rate dependence a − b shows only positive values, probably still in the “run-in” process where velocity strengthening is a common feature. With a normal stress of 300 MPa, the values of steady-state rate dependence decreases systematically with increasing temperature, and stick-slip occurred at 615 °C. Considering the limited displacement, limited normal stress applied and the effect of normal stress for the temperatures above 420 °C, it is inferred here that velocity weakening may be the typical behaviour at higher normal stress for temperature above 420 °C and at least up to 615 °C, which covers most of the temperature range in the lower crust of geologically stable continental interior. For a dry mafic lower crust in cool continental interiors where frictional sliding prevails over plastic flow, unstable slip nucleation may occur to generate earthquakes.  相似文献   

Uniaxial compression and tension tests of anthracite and loading rate dependence of peak strength   总被引：2，自引：0，他引：2  

S. Okubo  K. Fukui  Qi Qingxin 《International Journal of Coal Geology》2006,68(3-4):196-204

The mechanical characteristics of coal under uniaxial compressive stress and uniaxial tensile stress are key factors in investigations of the stability of galleries and coal faces, and are vital considerations for the efficient design of coalmines, disaster prevention, and environmental preservation. These mechanical characteristics have long been a topic of research, but remain insufficiently understood. In this study we performed uniaxial compression tests and uniaxial tension tests on coal, with particular attention to two concerns. The first was to measure the loading rate dependence of the peak strength of coal. Coal shows high sample-to-sample scatter in strength; test methods that are successful in comparatively homogeneous rock types cannot be used for coal. We therefore used an alternative test method that was recently developed by the authors. Anthracite samples were subjected to alternating slow and fast strain rates. Measured variations in stress during this process were used to estimate the loading rate dependence of peak strength. The second objective was to obtain complete stress–strain curves for coal under uniaxial tensile stress. It is difficult to hold samples secure during a tensile test; consequently, such curves have yet to be obtained. This study presents a successful application of the authors' method to the analysis of coal samples, yielding a complete stress–strain curve under tensile stress. The two methods presented here hold promise for application not only to anthracite but also to a wide variety of coals. It is possible to derive the values of the constants used in constitutive equations from the obtained experimental results. Once these equations are determined, they can be incorporated into finite-element software to investigate various time-dependent behaviors of coal and aid in the efficient design of coalmines and the prevention of subsidence and mine disasters.  相似文献   

Effects of dynamic shear strength and time-histories stress analysis on newmark sliding block analyses     

LI Hong-jun  CHI Shi-chun  LIN Gao 《岩土力学》2006,27(Z1):1063-1068

A simplified procedure for evaluating aseismic stability of slope subjected to earthquake shaking, in which the effect of dynamic shear strength and time-history stress on the yielding angular acceleration of sliding block is taken into account, is presented. The fundamental feature of this procedure is the dynamic shear strength. The numerical computations are performed by using the proposed method. It is shown that the computed sliding displacement for a given core dam, with either method of dynamic shear strength properly considered, is more rational compared with the conventional computational results based on static shear strength.  相似文献   

Three-dimensional model and late stage warping of the Plattengneis Shear Zone in the Eastern Alps     

Martin Putz  Kurt Stüwe  Mark Jessell  Philippe Calcagno   《Tectonophysics》2006,412(1-2):87-103

The Plattengneis shear zone is a 250–600 m thick, flat lying, Cretaceous, eclogite facies, mylonitic shear zone, with north-over-south transport direction, that is exposed over almost 1000 km² in the Koralpe region along the eastern margin of the Alps. Although the shear zone is one of the largest in the Alps, its role in the Eoalpine metamorphic evolution and the subsequent exhumation of the region, remain enigmatic and its large-scale geometry is not well understood. The outcrop pattern suggests that the shear zone is made up of a single sheet that is folded into a series of open syn- and antiforms with wavelengths of about 10 km. Eclogite bodies occur above, within and below the shear zone and there is no metamorphic grade change across the shear zone. In the south, the fold axes strike east–west and plunge shallowly to the east. In the north, the fold axes are oriented in north–south direction and form a dome shaped structure of the shear zone. Total shortening during this late stage warping event was of the order of 5%. Indirect evidence constrains this folding event to have occurred between 80 and 50 Ma and the fold geometry implies that the final exhumation in the Koralpe occurred somewhat later than further north. Interestingly, the shear zone appears to strike out of the topography in the south and dip into the topography in the north, so that north of the shear zone only hanging-wall rocks are exposed and south of it only foot-wall rocks. Possibilities for the geometric relationship of the Plattengneis shear zone with the surrounding south dipping detachments are discussed.  相似文献   

Up-temperature flow of surface-derived fluids in the mid-crust: the role of pre-orogenic burial of hydrated fault rocks   总被引：1，自引：0，他引：1  

C. CLARK  M.  HAND  K.  FAURE  A. SCHMIDT MUMM 《Journal of Metamorphic Geology》2006,24(5):367-387

The Walter‐Outalpa shear zone in the southern Curnamona Province of NE South Australia is an example of a shear zone that has undergone intensely focused fluid flow and alteration at mid‐crustal depths. Results from this study have demonstrated that the intense deformation and ductile shear zone reactivation, at amphibolite facies conditions of 534 ± 20 °C and 500 ± 82 MPa, that overprint the Proterozoic Willyama Supergroup occurred during the Delamerian Orogeny (c. 500 Ma) (EPMA monazite ages of 501 ± 16 and 491 ± 19 Ma). This is in contrast to the general belief that the majority of basement deformation and alteration in the southern Curnamona Province occurred during the waning stages of the Olarian Orogeny (c. 1610–1580 Ma). These shear zones contain hydrous mineral assemblages that cut wall rocks that have experienced amphibolite facies metamorphism during the Olarian Orogeny. The shear zone rock volumes have much lower δ¹⁸O values (as low as 1‰) than their unsheared counterparts (7–9‰), and calculated fluid δ¹⁸O values (5–8‰) consistent with a surface‐derived fluid source. Hydrous minerals show a decrease in δD_(H2O) from ?14 to ?22‰, for minerals outside the shear zones, to ?28 to ?40‰, for minerals within the shear zones consistent with a contribution from a meteoric source. It is unclear how near‐surface fluids initially under hydrostatic pressure penetrate into the middle crust where fluid pressures approach lithostatic, and where fluid flow is expected to be dominantly upward because of pressure gradients. We propose a mechanism whereby faulting during basin formation associated with the Adelaidean Rift Complex (c. 700 Ma) created broad hydrous zones containing mineral assemblages in equilibrium with surface waters. These panels of fault rock were subsequently buried to depths where the onset of metamorphism begins to dehydrate the fault rock volumes evolving a low δ¹⁸O fluid that is channelled through shear zones related to Delamerian Orogenic activity.  相似文献   

Effect of a submerged bay-mouth breakwater on tsunami behavior analyzed by 2D/3D hybrid model simulation     

Koji Fujima 《Natural Hazards》2006,39(2):179-193

The hybrid numerical model had been developed to simulate a complicated 3D flow around structures generated by tsunami. In the model, the conventional 2D model is adopted for the wide region far from structures and the 3D non-hydrostatic pressure model is used in the limited region adjacent to structures. The applicability of the model is shown by comparisons of the numerical results with the experimental results of the laboratory model tests and the numerical analysis results of the conventional whole 2D simulation. In addition, the effect of a submerged structure at the opening of a breakwater is discussed from the numerical simulations by the hybrid model. The submerged structure improves the stability of the rubble mound and reduces the tsunami inflow into the bay, while it increases the water surface velocity around the opening of the breakwater. The increase of surface velocity causes the increases of impulsive forces by collision with drafts and so on.  相似文献   

Strain softening of K0-consolidated Changi sand under plane-strain conditions     

D. Wanatowski  J. Chu 《Acta Geotechnica》2006,1(1):29-42

Experimental results are presented in this paper to study the strain softening behaviour of a marine dredged sand under plane-strain conditions. K₀ consolidated drained and undrained tests were conducted using a new plane-strain apparatus to characterize the strain softening behaviour of the sand under plane-strain conditions. For medium dense specimens, strain softening and shear bands were observed to occur under both drained and undrained conditions. For very loose specimens, no shear bands were observed and critical states were reached within the homogeneous deformation region in both drained and undrained tests. Strain softening was observed to occur at small strain for very loose specimens under undrained conditions. Two types of strain softening, the homogenous softening and banding softening, were identified and the conditions for strain softening were established. The results obtained from this study were compared with the studies by Han and Vardoulakis (Géotechnique 41(1):49–78, 1991), Finno et al. (J Geotech Eng ASCE 122(6):462–473, 1996, Géotechnique 47(1):149–165, 1997) and Mokni and Desrues (Mech Cohes-Frict Mat 4:419–441, 1998).  相似文献   

Assessment of Marine Clay Improvement Under Reclamation Fills by in-situ Testing Methods     

A. Arulrajah  H. Nikraz  M. W. Bo 《Geotechnical and Geological Engineering》2006,24(2):219-226

In ground improvement projects with prefabricated vertical drains, the duration of the preloading period is set in advance based on the predetermined time rate of consolidation of the compressible layer. If prediction is accurately done, the required degree of consolidation is met at the pre-determined preloading time. As such, there is a requirement for in-situ tests to be carried out just prior to the removal of surcharge to assess the degree of consolidation of the improved ground. In-situ tests were carried out after 23 months of surcharge loading at the In-Situ Test Site within the Changi East Reclamation Project in the Republic of Singapore. In-situ testing works in this research study comprises the use of field vane shear, piezocone, flat dilatometer and self-boring pressuremeter. The in-situ tests were carried out to determine the shear strength and degree of consolidation of the Singapore marine clay at Changi after 23 months of surcharge loading. The In-Situ Test Site consisted of a Vertical Drain Area as well as an untreated Control Area. Both areas were located adjacent to each other and were surcharged simultaneously to the same level and surcharge left in place for a period of 23 months. Comparison was made between the in-situ test results of the Vertical Drain Area and the untreated Control Area.  相似文献   

用强度折减法和FLAC^3D计算边坡的安全系数   总被引：4，自引：0，他引：4  

李新坡陈永波  王永杰何思明 王成华 《山地学报》2006,24(B10):235-239

对采用强度折减法和FLAC^3D计算边坡的安全系数问题进行了研究。对边坡破坏的判断标准、边坡滑面位置的确定及计算参数对安全系数计算结果的影响进行了分析。结果表明，用FLAC计算时，边坡的破坏可以通过节点最大不平衡力突变、节点最大速度突变、特定点位移的不收敛等特征进行判断，同时边坡破坏的滑面也可以由速度等值线图等方法表示出来。另外，通过分析发现，弹性常数、剪胀角等参数对安全系数计算结果的影响不大。  相似文献   

Automated SKS splitting and upper-mantle anisotropy beneath Canadian seismic stations   总被引：2，自引：0，他引：2  

M. S. Evans  J.-M. Kendall  R. J. Willemann 《Geophysical Journal International》2006,165(3):931-942

  相似文献